Showing posts with label How To. Show all posts
Showing posts with label How To. Show all posts

Sunday, June 22, 2014

How To: Install a Thermometer on Your Mash Tun

Over my last few batches I've been struggling getting consistent original gravity (OG) results.  I'm going to discuss my struggles and changes I've made in a bit more length in a future post, but one of the issues I considered was that I wasn't properly maintaining my mash temperature.  Controlling temperature (both during the mash and fermentation) is one of the challenges of home brewing.  Placing your strike water and grains in a cooler for an hour isn't an exact science and most home brewers don't have access to the same sophisticated equipment that a commercial brewery would use.

The simplest way to monitor your mash temperature would be to just drop your floating thermometer in your mash and check the temperature every so often.  The disadvantage of that process is losing heat each time you open your cooler.  I decided that I want to be able to monitor my mash temperature more closely to have a better idea of the temperatures during the mash.

Here's the process I used to install a thermometer on the outside of my mash tun (credits to John A who posted this procedure on a MoreBeer review of the stainless weld less thermometer kit).  The only challenge of this procedure is to not damage the interior cooler liner when you drill the larger hole for the thermometer bulkhead.  The procedure is very simple and could be done in less than 20 minutes as long as you don't have any leaks.

What you'll need:

Cooler mash tun
Stainless weld less thermometer (I used the 6 in variety, but the 2 in would probably work ok)
Drill
1" spade drill bit
1 1/2" spade drill bit

1.  Decide where to drill your hole for the thermometer.  Obviously this needs to be within the mash so you definitely want it below the 5 gallon mark on your cooler.  Also, don't place the hole too low to avoid trouble removing your false bottom.  I placed my hole about 4 3/4" above the ball valve at the bottom of my cooler.


2.  Drill a 1" hole with your spade bit.


3.  Drill a 1 1/2" hole with your spade bit.  This is part where you need to be careful.  The threads on the bulkhead are designed to fit through a 1" hole, but the depth of the threads is too short to fit through the entire wall of the cooler.  The 1 1/2" hole should go through the exterior liner and insulation only.  Do not damage the interior liner.


You can see from the photo that I mangled the exterior liner a bit.  If I were doing this again I would probably drill the larger hole first.

4.  Insert the thermometer and bulkhead through the new hole.  Sandwich the interior liner between the red rubber washer (this should go outside the liner) and stainless steel washer (inside the cooler).


5.  Tighten all your fittings, test for leaks and you're ready to get your mash on!



Monday, October 28, 2013

How To: Use a Counter Pressure Bottle Filler

Over the past few months since I went head over heels for kegging, one of the problems I've been facing is:

How do I get the carbonated beer out of the keg and into the bottle?

If you've ever tried to pour a beer directly from your tap into a bottle you're probably familiar with foam over flow that follows shortly after.  It's kind of like those 3rd grade volcano projects you did as a kid. This is usually followed by spilt beer, cursing, and tears of frustration (don't cry over spilt milk, but wasted beer is sinful).

On recent trip to MoreBeer! in Concord I invested in a Counter Pressure Bottle Filler. 

Counter Pressure Bottle Filler
This device is essentially a stainless steel tube with a 3-way valve at the top and a pressure relief valve on the side. 

I tested this gadget out this weekend on my Harvest Pumpkin Ale.  Through some trial and error this seems to be the least painful filling procedure:

1.  Clean and sanitize bottles and bottle fuller as your normally would. For me this includes PBW cleaner and Star San sanitizer. 

2. With the 3-way valve in the neutral position (perpendicular) and pressure relief valve closed, connect gas line and beverage lines to the top of the bottle filler. 

3.  Set the pressure on your regulator to 8-15 psi.  This was the pressure recommended by MoreBeer!, but I found that my typical serving pressure (5 psi) worked well too. 

4.  Insert the filler into your bottle so that the rubber stopper is snug inside the bottle. 

5.  Open the valve to the gas side and allow the bottle to fill with CO2. Once the bottle is full begin to open the pressure relief valve to allow air the escape. 

6.  Once you have air moving through the pressure relief valve you're ready to fill the bottle with beer. Move the 3-way valve to the beverage side. You can control the flow of beer into the bottle by adjusting the pressure relief valve. The more air you allow to escape, the faster the beer will flow into the bottle. 

Beer filling in progress...


This is what this process is supposed to avoid, head inside the bottle.  I need more practice.
7. When the bottle is full, move the 3-way valve back to the neutral position   Remove the bottle filler and cap the bottle immediately. 

A few things NOT to do:

- Do not try to stop the flow of beer using the pressure relief valve. This will only stop the flow of beer until you remove the filler. Once that happens the system is open, beer comes flowing out onto the floor of your garage, and you begin shouting. 

- Do not move the 3-way valve back to the gas position after the bottle has been filled.  Pushing gas into your beer is bad.

MoreBeer has a great video on their website detailing this process.  

Saturday, September 14, 2013

How To: Calculate Efficiency

If you've read my recent Harvest Pumpkin Ale post, you probably noticed that my OG was lower than that of the original author.

My OG = 1.060
Original Author OG = 1.070

This result was al little puzzling to me since I'm usually within a few points of the OG for the recipe I'm following.  I'm sure that my batch of beer will still be delicious and enjoyable, but this got me thinking about what could have caused the lower OG reading.  I had started with the author's original 10 gallon recipe and scaled it down to 6 gallons.  I later realized the original author had noted an expected efficiency of 85%.  When I planned my batch, the author's efficiency was something I ignored.  I've typically tried to avoid too many calculations in my brewing history, but I know that my efficiency is usually in the 70-80% range (I use a brewing app called iBrewMaster which calculates efficiency on its own).  To this point in my homebrewing career, efficiency has been a fun to follow stat (kind of like on base percentage in baseball), but hasn't really changed my brewing approach.

Here's my hypothesis and what I'm hoping to learn from this post:
The lower OG reading was a result of a lower efficiency than that of the original author and that I should have increased my grain bill to account for this.
Let's begin exploring this possibility.

First, let's learn how to calculate efficiency.  Referencing John Palmer's How To Brew, 2nd Edition, p. 151 (this link is for the 3rd edition):
"In mashing, you are collecting "x" number of gallons of wort that has a gravity of "1.0yy" that was produced from "z" pounds of malt.  To calculate your extraction in terms of PPG (points per pound per gallon), you need to multiply the number of gallons of wort you collected by its gravity and divide that by the amount of malt that was used."
x = gallons of wort
yy = maximum PPG (reference this table, max PPG is the last two digits of the potential SG)
z = pounds of malt

PPG = yy*z/x

I'm going to begin by calculating efficiency for a very simple batch of beer, Be-Otch IPA.  Here is the grain bill with the efficiency calculation (I collected 6 gallons of wort)

14 lbs US 2 row pale malt          (36 x 14) / 6 = 84 max PPG
0.6 lbs Caramel/Crystal 20L      (35 x 0.6) / 6 = 3.5 max PPG


14.6 lbs total                               87.6 max PPG

Max PPG would be the specific gravity (1.087) if you were able to achieve 100% efficiency.  In this case I know that my gravity reading was 1.063

Efficiency = 63/87 = 72%

Now let's try this with my Harvest Pumpkin Ale.  Note, I'm ignoring the rice hulls since they do not contribute any sugars to the mash.

11.4 lbs 6-Row Pale Malt         (35 x 11.4) / 6 = 66.5
0.75 lbs Melanoiden Malt         (37 x 0.75) / 6 = 4.6
0.6 lbs Crystal 60                      (34 x 0.6) / 6 = 3.4

0.6 lbs Victory Malt                  (36 x 0.6) / 6 = 3.6

13.35 lbs total                            78.1 max PPG

OG reading = 1.060

Efficiency = 60/78 = 77%

As expected, my efficiency was lower than the 85% recommended by the original author.  If I was to do this batch again, I would probably assume an efficiency of 75% and increase my grain bill by enough to compensate for my less efficient operation.  To calculate my grain increase I'm going to take the original max PPG (78.1) and multiply that by the recommended 85% efficiency to get my target PPG.

78.1 x 85% = 66.3 target PPG

Next, I'll take the target PPG and divide that by my assumed efficiency of 75% to get my new max PPG.

66.3 / 75% = 88.5 new max PPG

Finally, I'll divide my new max PPG by the original max PPG to determine the percent increase for each of the grains and multiply that increase percentage by each grain in the recipe.

88.5 / 78.1 = 113%

Revised grain bill:

12.9 lbs 6-Row Pale Malt         (35 x 12.9) / 6 = 75.3
0.85 lbs Melanoiden Malt         (37 x 0.85) / 6 = 5.2
0.7 lbs Crystal 60                      (34 x 0.7) / 6 = 4.0

0.7 lbs Victory Malt                  (36 x 0.7) / 6 = 4.2

15.15 lbs total                            88.7 max PPG

After doing this exercise, efficiency is not just another stat to be ignored.  You can see that this makes a significant difference in the grain bill (1.8 lbs!!).  If I were brewing this recipe on a large scale, efficiency would be a huge deal and could cost thousands of dollars.  On the homebrewing scale its only a few extra dollars out of my pocket.  If you're planning recipes in the future, whether its from a magazine or book try to find out what the assumed efficiency is and if it is similar to your system.  The exercise above only take a few minutes and could make a difference in the final product of your batch.

But if you hate math and just enjoy brewing for fun, ignore this post, relax, and have a homebrew!!

Sunday, September 1, 2013

How To: Make A Yeast Starter

A few years ago I was sitting at work on a Saturday, not thinking about work, but thinking about ways to improve my beer.  After spending some time on Google, I found that making a yeast starter was an easy and inexpensive step to improve beer.  I usually try to make my starter the day before I brew.  Sometimes I forget, take a deep breath, and I make the starter the morning of brew day (this is usually is enough time for the starter to get moving and begin creating additional yeast).  I think that any head start you give the yeast is better than nothing.  This is good for your beer because full on fermentation will begin sooner, minimize the risk of infection, and will lead to a healthier fermentation.  Healthy fermentation = delicious beer!!!

This is the procedure I follow for 5 gallon batches of beer.  If you're brewing 10 gallon size batches, you'll probably want to double everything in the procedure.

Here's what you'll need:

Yeast (duh!)
1000 mL Erlenmeyer flask w/ stopper
Funnel
Light Dried Malt Extract (DME)
Saucepan
Stirring Spoon
Lighting reading (optional)
Whiskey (see background, also optional, but leads to more fun!)

Here's what you need!

Now for the procedure.  This is very simple.  You're basically making a very smaller batch of wort to get the yeast going.

1.  Clean and sanitize all your equipment that will come in contact with the wort.  I use PBW and Star San like I do for brewing full batches.  However, you should clean and sanitize using whatever method you're used to.

2.  Bring 650 mL of water to a boil in the saucepan.  Add 1/2 cup of the light DME to the boiling water and stir until the DME dissolves.  When you add the DME it will boil over.  Be prepared to lift the pan off the stove.  Once the wort calms down, continue to boil for 15 minutes.

Note:  I've tried performing the boil directly in the Erlenmeyer flask, but have had a very difficult time controlling the boil over.  The flask tends to act like a 3rd grade volcano project and erupts every 30 seconds during the boil.

Ready for boil over!

Boil over gone!
3.  Before the end of the boil prepare a small ice bath.  Once the boil is complete, transfer the boiled wort into the Erlenmeyer flask.  Place the flask into the ice bath and wrap the flask in a cold, wet towel.  The wort should be cooled in about 10-15 minutes.

This isn't the most impressive ice bath, but it doesn't need to be for your starter.

4.  Once the starter has cooled to room temperature.  You're ready to pitch your yeast.  For this particular batch, I'm using White Labs California Ale WLP001.  Swirl the yeast around inside the vial to be sure none is stuck to the sides and pitch into the flask.  If you're using a Wyeast smack pack, perform the smack! as your normally would pitching into a full batch of wort.  Swirl the flask after you've pitched the yeast to throughly mix the yeast with the wort.  Place your stopper and let sit for about 24 hours.  You're done!

Pre-pitch

White Labs Yeast Vial

Post pitch
All told, this take less than an hour and I've had success using this method for more consistent fermentation in the full batch.  Remember to pitch the entire starter into your batch.  This will not affect the flavor of your particular style.

One additional step that can be performed is to place the starter on a stir plate to continually oxygenize the starter.  I don't use a stir plate and would recommend that a stir plate is strictly optional.  If you're in the cool chemistry lab stuff, then by all means one.  If you're on a budget, you can skip the stir plate and still make a great starter.

UPDATE:

By popular demand here is a shot of the yeast starter right before I pitched into my pumpkin ale yesterday.

Yeast Starter on Brew Day - 9/2/2013